china table

1) we previously ordered the smaller 60cmx120cm table that used the correct 2inchx1inch table frame making it stable;

2) the new bigger table with dimension 70cmx140cm used the incorrect thinner 1.5inchx0.75inch table frame making the table unstable and wiggling/shaky in the middle. Note: There are zero good engineers who will agree with your incorrect poor cost cutting engineering design to use 2inchx1inch for a smaller glass desk(60x120cm)and then use a thinner 1.5inchx0.75inch for a bigger glass desk (70x140cm). We are extremely dissatisfied and absolutely disappointed with your engineering, design and management team. why would you deliver a substandard low quality product to us?

3) the glass and the frame are not attached to each other such that it vibrates; can we use an adhesive like silicon to attach the glass to the metal frame to prevent it from vibrating or shaking? we are afraid that markings might appear on top if we do, what should be used so no marking will appear on top when an adhesive dries up to attach the glass to the metal? or adhesive like silicone should not be used?

4) you should have added 1 glass attachment fastening tightening device that you used at the corners to tighten the glass to the metal frame and added 1 in the top middle portion between the top left and top right portion to prevent the glass from flapping causing a vibration everytime you put your hands on the table. the flapping vibration is coming from glass to metal contact in the middle portion when you rest your hands on top. the design in obviously wrong;
a) incorrect frame size bec you used substandard undersize metal frame(0.75x1.5 inches) for the bigger table while the smaller table was perfect (1x2 inches);
b) glass to metal gap cause flapping vibration when hand is placed on top bec you should have added 1 glass to metal tighening device you used at the corner & you should have added it in the top middle portion colinear with the top left and top right so that there would be no gap between glass and metal that will cause flapping vibration.

5) the drawer in the smaller table is deeper at 2 inches because you used a 2 inch frame while the bigger table is bad and the drawer is shallow at just 1.5 inches bec you used low quality substandard undersize frame for the bigger table. the smaller table also has a better drawer mechanism pull to open, the big table has a terrible push to open mechanism that has the huge tendency to misalign;

6) the big table has an incorrect foot rest bar design at the bottom, customers who do not want the foot rest metal bar and decides not to install it will see 2 ugly metal extension protruding at the left and right side of the vertical stand that can cause wound, the customers are forced to cover the protruding metal bars with ugly cushion to prevent accidental leg to metal contact injury underneath the table.

1) 我们之前订购了较小的 60cmx120cm 桌子，该桌子使用了正确的 2inchx1inch 桌子框架，使其稳定；

2）尺寸为 70 厘米 x 140 厘米的新更大桌子使用了不正确的更薄的 1.5 英寸 x 0.75 英寸桌框，导致桌子不稳定并在中间摆动/摇晃。注意：有零个优秀的工程师会同意您错误的、糟糕的成本削减工程设计，即使用 2 英寸 x 1 英寸用于较小的玻璃桌子（60 x 120 厘米），然后使用更薄的 1.5 英寸 x 0.75 英寸用于较大的玻璃桌子（70 x 140 厘米）。我们对你们的工程、设计和管理团队非常不满意，绝对失望。为什么你们要向我们提供不合格的低质量产品？

3）玻璃与框架没有相互贴合而产生振动；我们可以使用硅胶等粘合剂将玻璃固定在金属框架上以防止其振动或晃动吗？我们担心如果这样做的话，顶部可能会出现标记，应该使用什么，这样当粘合剂干燥以将玻璃粘合到金属上时，顶部不会出现标记？或者不应该使用硅胶之类的粘合剂？

4) 您应该添加 1 个玻璃附件紧固装置，用于在拐角处将玻璃紧固到金属框架上，并在左上角和右上部分之间的顶部中间部分添加 1 个，以防止玻璃拍打导致每次将手放在桌子上时都会振动。当您将手放在上面时，拍打振动来自中间部分的玻璃与金属接触。设计明显错误；
a) 框架尺寸不正确，因为您在较大的桌子上使用了不合标准的小尺寸金属框架（0.75x1.5 英寸），而较小的桌子是完美的（1x2 英寸）；
b) 当手放在顶部时，玻璃与金属的间隙会导致拍打振动，因为您应该在拐角处使用的金属紧固装置中添加 1 个玻璃，并且您应该将其添加到与左上角和右上角共线的顶部中间部分使玻璃与金属之间不存在产生拍打振动的间隙。

5) 小桌子上的抽屉更深，为 2 英寸，因为您使用了 2 英寸框架，而较大的桌子很糟糕，抽屉很浅，只有 1.5 英寸，因为您为大桌子使用了低质量、不合格的尺寸过小的框架。小桌子也有更好的抽屉机构拉开，大桌子有一个可怕的推开机构，有很大的错位倾向；

6）大桌子底部的搁脚杆设计不正确，不想要搁脚金属杆并决定不安装的顾客会看到立式支架左右两侧突出了2个丑陋的金属延伸部分，可能会造成伤口，顾客被迫用丑陋的垫子盖住突出的金属条，以防止桌子下面的腿与金属意外接触受伤。